{"id":15730,"date":"2026-06-16T11:40:26","date_gmt":"2026-06-16T03:40:26","guid":{"rendered":"https:\/\/www.drillpipes.com\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/"},"modified":"2026-09-18T16:02:39","modified_gmt":"2026-09-18T08:02:39","slug":"api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared","status":"publish","type":"post","link":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/","title":{"rendered":"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection: E75, X95, G105 and S135 CoMPared"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\"><strong>API 5DP Drill Pipe Grade Selection<\/strong> compares <strong>E75, X95, G105 and S135<\/strong> by strength level, load condition and drill string performance. E75 starts at <strong>75 ksi minimum yield strength<\/strong>, X95 at <strong>95 ksi<\/strong>, G105 at <strong>105 ksi<\/strong> and S135 at <strong>135 ksi<\/strong>, but grade selection should not move upward only because the number is higher. E75 is normally reviewed for moderate tensile and torque demand, X95 for added load margin, G105 for deeper or directional drilling, and S135 for high hook load, long horizontal sections or higher torque conditions. The correct grade should match the full load path, including dogleg severity, fatigue exposure, OD \/ wall thickness, upset type, tool joint condition, connection capacity and traceable inspection records.<\/p>\n\n<h2 class=\"wp-block-heading\">API 5DP tuber\u00eda de perforaci\u00f3n grados and Mechanical Properties<\/h2>\n\n<p class=\"wp-block-paragraph\"><strong><a href=\"https:\/\/www.drillpipes.com\/es\/%d0%b1%d1%83%d1%80%d0%b8%d0%bb%d1%8c%d0%bd%d0%b0%d1%8f-%d1%82%d1%80%d1%83%d0%b1%d0%b0-api-5dp\/\">API 5DP Drill Pipe<\/a> Grades<\/strong> should be read as the mechanical acceptance baseline for the pipe body, not as a complete drill string selection result. The strength window of each grade needs to be checked together with pipe size, wall thickness, upset geometry, weld zone, tool joint configuration, connection type, hardness \/ impact requirements where applicable, and traceable inspection records. This approach keeps the grade comparison tied to real drill pipe performance rather than only to yield-strength numbers.<\/p>\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-center\" data-align=\"center\">API 5DP grado<\/th><th class=\"has-text-align-center\" data-align=\"center\">Minimum l\u00edmite el\u00e1stico<\/th><th class=\"has-text-align-center\" data-align=\"center\">Maximum l\u00edmite el\u00e1stico<\/th><th class=\"has-text-align-center\" data-align=\"center\">Minimum resistencia a la tracci\u00f3n<\/th><\/tr><\/thead><tbody><tr><td class=\"has-text-align-center\" data-align=\"center\">E75<\/td><td class=\"has-text-align-center\" data-align=\"center\">75 ksi \/ 517 MPa<\/td><td class=\"has-text-align-center\" data-align=\"center\">105 ksi \/ 724 MPa<\/td><td class=\"has-text-align-center\" data-align=\"center\">100 ksi \/ 689 MPa<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">X95<\/td><td class=\"has-text-align-center\" data-align=\"center\">95 ksi \/ 655 MPa<\/td><td class=\"has-text-align-center\" data-align=\"center\">125 ksi \/ 862 MPa<\/td><td class=\"has-text-align-center\" data-align=\"center\">105 ksi \/ 724 MPa<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">G105<\/td><td class=\"has-text-align-center\" data-align=\"center\">105 ksi \/ 724 MPa<\/td><td class=\"has-text-align-center\" data-align=\"center\">135 ksi \/ 931 MPa<\/td><td class=\"has-text-align-center\" data-align=\"center\">115 ksi \/ 793 MPa<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">S135<\/td><td class=\"has-text-align-center\" data-align=\"center\">135 ksi \/ 931 MPa<\/td><td class=\"has-text-align-center\" data-align=\"center\">165 ksi \/ 1138 MPa<\/td><td class=\"has-text-align-center\" data-align=\"center\">145 ksi \/ 1000 MPa<\/td><\/tr><\/tbody><\/table><\/figure>\n\n<div data-wp-interactive=\"core\/file\" class=\"wp-block-file\"><object data-wp-bind--hidden=\"!state.hasPdfPreview\" hidden class=\"wp-block-file__embed\" data=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grades-Mechanical-Strength-Reference.pdf\" type=\"application\/pdf\" style=\"width:100%;height:600px\" aria-label=\"Incrustado de API 5DP Drill Pipe Grades Mechanical Strength Reference.\"><\/object><a id=\"wp-block-file--media-b4cff3d9-204c-4bcb-98fd-845539da9ae2\" href=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grades-Mechanical-Strength-Reference.pdf\">API 5DP tuber\u00eda de perforaci\u00f3n grados Mechanical Strength Reference<\/a><a href=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grades-Mechanical-Strength-Reference.pdf\" class=\"wp-block-file__button wp-element-button\" download=\"\" aria-describedby=\"wp-block-file--media-b4cff3d9-204c-4bcb-98fd-845539da9ae2\">Download<\/a><\/div>\n\n<p class=\"wp-block-paragraph\">From E75 to S135, the yield-strength window increases, but the grado should still be reviewed against the complete tuber\u00eda de perforaci\u00f3n assembly. For G105 and S135, higher tuber\u00eda body strength can shift the limiting point toward the upset transition, rosca area, uni\u00f3n shoulder or uni\u00f3n-side fatiga.<\/p>\n\n<figure class=\"wp-block-gallery has-nested-images columns-default is-cropped wp-block-gallery-1 is-layout-flex wp-block-gallery-is-layout-flex\">\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"768\" data-id=\"13551\" src=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/drill-pipe-mechanical-properties-1024x768.jpg\" alt=\"\" class=\"wp-image-13551\" srcset=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/drill-pipe-mechanical-properties-1024x768.jpg 1024w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/drill-pipe-mechanical-properties-300x225.jpg 300w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/drill-pipe-mechanical-properties.jpg 1448w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n<\/figure>\n\n<h2 class=\"wp-block-heading\">E75 vs X95 vs G105 vs S135 tuber\u00eda de perforaci\u00f3n grado Selection CoMParison<\/h2>\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-center\" data-align=\"center\">API 5DP grado<\/th><th>Typical Review Condition<\/th><th>Main Control Point<\/th><th>Next Review Step<\/th><\/tr><\/thead><tbody><tr><td class=\"has-text-align-center\" data-align=\"center\"><strong>E75 Drill Pipe<\/strong><\/td><td>Conventional vertical pozos, moderate tensile load and normal rotaria par<\/td><td>gancho load, OD \/ espesor de pared, uni\u00f3n match and basic inspection records<\/td><td>Review X95 when tensile margin becomes limited or directional load increases<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\"><strong>X95 Drill Pipe<\/strong><\/td><td>Medium-depth pozos, controlled directional sections and moderate par increase<\/td><td>Tensile margin, par demand, bending load and uni\u00f3n coMPatibility<\/td><td>Review G105 when X95 no longer provides enough load margin<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\"><strong>G105 Drill Pipe<\/strong><\/td><td>Deeper pozos, perforaci\u00f3n direccional, controlled horizontal sections and higher combined load<\/td><td>par-arrastre, dogleg severity, cyclic bending, uni\u00f3n strength and uni\u00f3n review<\/td><td>Review S135 when gancho load, long horizontal rotation or bending fatiga approaches the G105 margin<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\"><strong>S135 Drill Pipe<\/strong><\/td><td>pozo profundos, high gancho load, long horizontal sections, ERD or high-par perforaci\u00f3n<\/td><td>fatiga exposure, uni\u00f3n par, shoulder contact, uni\u00f3n matching and hardness \/ toughness review<\/td><td>Review a special material route when sour service, low-temperature toughness or severe fatiga controls the design<\/td><\/tr><\/tbody><\/table><\/figure>\n\n<p class=\"wp-block-paragraph\"><mark style=\"background-color:rgba(0, 0, 0, 0)\" class=\"has-inline-color has-primary-color\">E75, X95, G105 and S135<\/mark> each have a suitable review range, and the final grade should match the well profile, fatigue exposure, connection capacity and inspection evidence.<\/p>\n\n<h2 class=\"wp-block-heading\">E75 tuber\u00eda de perforaci\u00f3n: Baseline grado for Moderate perforaci\u00f3n Load<\/h2>\n\n<p class=\"wp-block-paragraph\"><strong><a href=\"https:\/\/www.drillpipes.com\/es\/%d0%b1%d1%83%d1%80%d0%b8%d0%bb%d1%8c%d0%bd%d0%b0%d1%8f-%d1%82%d1%80%d1%83%d0%b1%d0%b0-e75\/\">E75 Drill Pipe<\/a><\/strong> provides the baseline API 5DP strength level, with <strong>75 ksi \/ 517 MPa minimum yield strength<\/strong>, <strong>105 ksi \/ 724 MPa maximum yield strength<\/strong> and <strong>100 ksi \/ 689 MPa minimum tensile strength<\/strong>. It is reviewed for drilling programs where tensile load, torque, bending cycle and connection demand remain within a moderate range. Its role is not to compete with G105 or S135 in high-load sections, but to provide a stable grade basis where the well profile, OD \/ wall thickness, upset type and connection have enough design margin.<\/p>\n\n<p class=\"wp-block-paragraph\">E75 is more suitable when:<\/p>\n\n<ul class=\"wp-block-list\">\n<li>the pozo is vertical or only moderately directional<\/li>\n\n\n\n<li>gancho load and par remain within a controlled range<\/li>\n\n\n\n<li>dogleg severity is not a major fatiga driver<\/li>\n\n\n\n<li>no severe sour-service or low-temperature toughness requirement controls the design<\/li>\n\n\n\n<li>the selected size, espesor de pared and uni\u00f3n provide enough design margin<\/li>\n<\/ul>\n\n<p class=\"wp-block-paragraph\">E75 becomes less suitable when the pozo moves toward higher tensile load, longer directional sections, higher par or repeated bending conditions. In that case, the grado review usually moves toward X95, G105 or S135.<\/p>\n\n<h2 class=\"wp-block-heading\">X95 tuber\u00eda de perforaci\u00f3n: Intermediate Strength Between E75 and G105<\/h2>\n\n<p class=\"wp-block-paragraph\"><strong>X95 Drill Pipe<\/strong> provides an intermediate API 5DP strength level, with <strong>95 ksi \/ 655 MPa minimum yield strength<\/strong>, <strong>125 ksi \/ 862 MPa maximum yield strength<\/strong> and <strong>105 ksi \/ 724 MPa minimum tensile strength<\/strong>. It is selected when E75 does not provide enough tensile-load margin, but the well profile still does not require G105 or S135. The review should focus on medium-depth drilling, controlled directional sections, increased torque demand and limited fatigue exposure.<\/p>\n\n<p class=\"wp-block-paragraph\">X95 is commonly reviewed for:<\/p>\n\n<ul class=\"wp-block-list\">\n<li>medium-depth pozos with higher tension than E75 can comfortably support<\/li>\n\n\n\n<li>controlled directional pozos<\/li>\n\n\n\n<li>perforaci\u00f3n sections with increased par but limited severe fatiga exposure<\/li>\n\n\n\n<li>applications where G105 or S135 may be more strength than the load case requires<\/li>\n\n\n\n<li>sarta de perforaci\u00f3ns where uni\u00f3n coMPatibility and inspection records still support tramoard API grado review<\/li>\n<\/ul>\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/www.drillpipes.com\/es\/x95-vs-g105-tuberia-de-perforacion\/\">The difference between X95 and G105 <\/a>is not only a 10 ksi minimum yield-strength increase. The review should also consider whether the extra strength is needed for the actual load path. If the limiting factor is connection torque, dogleg fatigue or tool joint condition, moving to a higher pipe body grade alone may not solve the problem.<\/p>\n\n<h2 class=\"wp-block-heading\">G105 tuber\u00eda de perforaci\u00f3n: Higher Strength for Deeper or Directional pozos<\/h2>\n\n<p class=\"wp-block-paragraph\"><strong><a href=\"https:\/\/www.drillpipes.com\/es\/%d0%b1%d1%83%d1%80%d0%b8%d0%bb%d1%8c%d0%bd%d0%b0%d1%8f-%d1%82%d1%80%d1%83%d0%b1%d0%b0-g105\/\">G105 Drill Pipe<\/a><\/strong> provides <strong>105 ksi \/ 724 MPa minimum yield strength<\/strong>, <strong>135 ksi \/ 931 MPa maximum yield strength<\/strong> and <strong>115 ksi \/ 793 MPa minimum tensile strength<\/strong>. It offers a higher strength window than X95, but remains below S135, making it suitable for medium-to-deep directional wells, controlled horizontal sections and drilling intervals where torque, tension and cyclic bending increase but a high-strength S135 route is not yet required.<\/p>\n\n<p class=\"wp-block-paragraph\">G105 grado review should include:<\/p>\n\n<ul class=\"wp-block-list\">\n<li>tensile-load margin under planned pozo depth<\/li>\n\n\n\n<li>par and arrastre along the directional section<\/li>\n\n\n\n<li>uni\u00f3n size, uni\u00f3n type and shoulder contact<\/li>\n\n\n\n<li>tuber\u00eda marking, MTC and heat number traceability<\/li>\n<\/ul>\n\n<p class=\"wp-block-paragraph\">A <strong>G105 tuber\u00eda de perforaci\u00f3n<\/strong> selection is usually reasonable when the main requirement is higher tuber\u00eda body strength, while fatiga, uni\u00f3n and service-environment risks remain controlled. If the pozo profile includes long lateral rotation, high par, severe dogleg or sour-service exposure, G105 still needs a deeper performance review instead of being selected by grado name alone.<\/p>\n\n<h2 class=\"wp-block-heading\">S135 tuber\u00eda de perforaci\u00f3n: High-Strength API grado for Higher Load Conditions<\/h2>\n\n<p class=\"wp-block-paragraph\"><strong><a href=\"https:\/\/www.drillpipes.com\/es\/%d0%b1%d1%83%d1%80%d0%b8%d0%bb%d1%8c%d0%bd%d0%b0%d1%8f-%d1%82%d1%80%d1%83%d0%b1%d0%b0-s135\/\">S135 Drill Pipe<\/a><\/strong> provides the common high-strength API baseline in this grade group. With a 135 ksi minimum yield-strength level, it is normally reviewed for deep wells, high hook load, long horizontal sections and drilling programs where the drill string needs a larger tensile-strength margin.<\/p>\n\n<p class=\"wp-block-paragraph\">S135 is important because it expands the available strength window beyond E75, X95 and G105. But it should not be treated as the automatic best answer. Higher strength also makes toughness, hardness, fatiga-sensitive geometry and uni\u00f3n-side performance more important.<\/p>\n\n<p class=\"wp-block-paragraph\">S135 should be reviewed carefully when:<\/p>\n\n<ul class=\"wp-block-list\">\n<li>gancho load approaches the practical margin of G105<\/li>\n\n\n\n<li>long horizontal or ERD sections increase par and arrastre<\/li>\n\n\n\n<li>high dogleg severity creates repeated bending stress<\/li>\n\n\n\n<li>high make-up par requires stronger uni\u00f3n review<\/li>\n\n\n\n<li>uni\u00f3n matching becomes critical to sarta de perforaci\u00f3n performance<\/li>\n\n\n\n<li>hardness, toughness or cracking risk may control the service condition<\/li>\n<\/ul>\n\n<p class=\"wp-block-paragraph\">For sour-service or H2S-containing environments, S135 should not be selected only because it has high strength. Sour-service use requires separate qualification logic, hardness control, cracking-risk review and project-specific acceptance requirements. A high-strength grado without the equipo de perforaci\u00f3nht service basis can create risk rather than solve it.<\/p>\n\n<div class=\"wp-block-columns is-layout-flex wp-container-core-columns-is-layout-0e47273b wp-block-columns-is-layout-flex\">\n<div class=\"wp-block-column is-layout-flow wp-block-column-is-layout-flow\">\n<figure class=\"wp-block-gallery has-nested-images columns-default is-cropped wp-block-gallery-2 is-layout-flex wp-block-gallery-is-layout-flex\">\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"768\" data-id=\"13553\" src=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grades-1-1024x768.jpg\" alt=\"\" class=\"wp-image-13553\" srcset=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grades-1-1024x768.jpg 1024w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grades-1-300x225.jpg 300w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grades-1.jpg 1448w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n<\/figure>\n<\/div>\n\n\n\n<div class=\"wp-block-column is-layout-flow wp-block-column-is-layout-flow\">\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"768\" src=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/E75-Drill-Pipe-1-1024x768.jpg\" alt=\"\" class=\"wp-image-13554\" srcset=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/E75-Drill-Pipe-1-1024x768.jpg 1024w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/E75-Drill-Pipe-1-300x225.jpg 300w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/E75-Drill-Pipe-1.jpg 1448w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n<\/div>\n<\/div>\n\n<h2 class=\"wp-block-heading\">G105 vs S135 tuber\u00eda de perforaci\u00f3n: Strength Difference and Selection Logic<\/h2>\n\n<p class=\"wp-block-paragraph\"><strong><a href=\"https:\/\/www.drillpipes.com\/es\/g105-vs-s135-tuberia-de-perforacion\/\">G105 vs S135 Drill Pipe<\/a><\/strong> is one of the most important comparisons in API 5DP grade selection. S135 has a higher minimum yield strength than G105, but this does not mean S135 is always the better choice.<\/p>\n\n<p class=\"wp-block-paragraph\">The correct grado is determined by the limiting load path. G105 is usually enough when gancho load, par-arrastre, dogleg severity and uni\u00f3n capacity remain within the reviewed margin. S135 becomes more relevant when long horizontal rotation, high gancho load or severe bending increases fatiga exposure near the upset transition, uni\u00f3n or rosca shoulder. If the limiting point is uni\u00f3n par, shoulder contact, iMPact toughness or service condition, increasing tuber\u00eda body l\u00edmite el\u00e1stico alone does not improve the actual sarta de perforaci\u00f3n selection.<\/p>\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-center\" data-align=\"center\">Review Item<\/th><th>G105 Selection Basis<\/th><th>S135 Selection Basis<\/th><\/tr><\/thead><tbody><tr><td class=\"has-text-align-center\" data-align=\"center\">Tensile load<\/td><td>G105 provides enough design margin for the planned gancho load and sarta de perforaci\u00f3n peso.<\/td><td>gancho load approaches or exceeds the practical margin of G105.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">pozo profile<\/td><td>Directional sections are controlled, and dogleg severity remains moderate.<\/td><td>Long horizontal, ERD or severe dogleg sections increase bending and fatiga exposure.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">par demand<\/td><td>uni\u00f3n and uni\u00f3n capacity remain within the reviewed par range.<\/td><td>High par, shoulder loading or repeated make-up makes uni\u00f3n review critical.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">fatiga risk<\/td><td>Rotation and bending cycles remain within normal grado review.<\/td><td>Repeated bending near the upset transition or uni\u00f3n area becomes a key control point.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Service condition<\/td><td>No severe sour-service, low-temperature or special toughness requirement controls the grado.<\/td><td>Hardness, toughness, cracking resistance or service qualification requires stricter review.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Inspection evidence<\/td><td>tramoard API grado records support the selected size, grado and uni\u00f3n.<\/td><td>Additional review of toughness, hardness, uni\u00f3n matching and traceability records is required.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n<p class=\"wp-block-paragraph\">G105 is often a higher-strength working grado for deeper or perforaci\u00f3n direccional, while S135 is reviewed when the load case needs a high-strength API grado. Neither grado should be selected without checking the uni\u00f3n, fatiga exposure and inspection evidence.<\/p>\n\n<div data-wp-interactive=\"core\/file\" class=\"wp-block-file\"><object data-wp-bind--hidden=\"!state.hasPdfPreview\" hidden class=\"wp-block-file__embed\" data=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/G105-vs-S135-Drill-Pipe-Selection-Review.pdf\" type=\"application\/pdf\" style=\"width:100%;height:600px\" aria-label=\"Incrustado de G105 vs S135 Drill Pipe Selection Review.\"><\/object><a id=\"wp-block-file--media-d28ebd91-2eee-485c-92c7-7c36a3e4a213\" href=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/G105-vs-S135-Drill-Pipe-Selection-Review.pdf\">G105 vs S135 tuber\u00eda de perforaci\u00f3n Selection Review<\/a><a href=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/G105-vs-S135-Drill-Pipe-Selection-Review.pdf\" class=\"wp-block-file__button wp-element-button\" download=\"\" aria-describedby=\"wp-block-file--media-d28ebd91-2eee-485c-92c7-7c36a3e4a213\">Download<\/a><\/div>\n\n<h2 class=\"wp-block-heading\">grado Selection by perforaci\u00f3n Condition<\/h2>\n\n<p class=\"wp-block-paragraph\">Before selecting E75, X95, G105 or S135, the review should separate load demand from failure risk. vertical pozos are mainly controlled by tensile load and normal par, while long horizontal or ERD pozos are controlled by par-arrastre, cyclic bending and uni\u00f3n-side fatiga. Sour-service or low-temperature perforaci\u00f3n requires hardness, iMPact toughness and cracking-resistance review beyond l\u00edmite el\u00e1stico.<\/p>\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-center\" data-align=\"center\">perforaci\u00f3n Condition<\/th><th class=\"has-text-align-center\" data-align=\"center\">Common grado Review<\/th><th>Key Control Point<\/th><\/tr><\/thead><tbody><tr><td class=\"has-text-align-center\" data-align=\"center\">Conventional vertical pozo<\/td><td class=\"has-text-align-center\" data-align=\"center\">E75 \/ X95<\/td><td>Tensile load, normal par, basic inspection records<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Medium-depth directional pozo<\/td><td class=\"has-text-align-center\" data-align=\"center\">X95 \/ G105<\/td><td>par, bending load, uni\u00f3n coMPatibility<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">pozo profundo<\/td><td class=\"has-text-align-center\" data-align=\"center\">G105 \/ S135<\/td><td>gancho load, tensile margin, uni\u00f3n strength<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Long horizontal pozo<\/td><td class=\"has-text-align-center\" data-align=\"center\">G105 \/ S135<\/td><td>par-arrastre, fatiga, dogleg severity<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">ERD pozo<\/td><td class=\"has-text-align-center\" data-align=\"center\">S135 or special route review<\/td><td>Combined tension, par, arrastre and fatiga<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">High-par perforaci\u00f3n<\/td><td class=\"has-text-align-center\" data-align=\"center\">G105 \/ S135<\/td><td>Make-up par, shoulder contact, rosca condition<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Sour-service or H2S exposure<\/td><td class=\"has-text-align-center\" data-align=\"center\">Sour-service route review<\/td><td>Hardness, SSC risk and service qualification basis<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Low-temperature perforaci\u00f3n<\/td><td class=\"has-text-align-center\" data-align=\"center\">grado plus toughness review<\/td><td>Charpy test temperature and absorbed energy requirement<\/td><\/tr><\/tbody><\/table><\/figure>\n\n<figure class=\"wp-block-gallery has-nested-images columns-default is-cropped wp-block-gallery-3 is-layout-flex wp-block-gallery-is-layout-flex\">\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"768\" data-id=\"13552\" src=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/E75-vs-X95-vs-G105-vs-S135-1024x768.jpg\" alt=\"\" class=\"wp-image-13552\" srcset=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/E75-vs-X95-vs-G105-vs-S135-1024x768.jpg 1024w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/E75-vs-X95-vs-G105-vs-S135-300x225.jpg 300w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/E75-vs-X95-vs-G105-vs-S135.jpg 1448w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n<\/figure>\n\n<div data-wp-interactive=\"core\/file\" class=\"wp-block-file\"><object data-wp-bind--hidden=\"!state.hasPdfPreview\" hidden class=\"wp-block-file__embed\" data=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection-Matrix-by-Drilling-Condition.pdf\" type=\"application\/pdf\" style=\"width:100%;height:600px\" aria-label=\"Incrustado de API 5DP Drill Pipe Grade Selection Matrix by Drilling Condition.\"><\/object><a id=\"wp-block-file--media-9fb9465d-d03e-4c90-b2d7-109f3b70d3c2\" href=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection-Matrix-by-Drilling-Condition.pdf\">API 5DP tuber\u00eda de perforaci\u00f3n grado Selection Matrix by perforaci\u00f3n Condition<\/a><a href=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection-Matrix-by-Drilling-Condition.pdf\" class=\"wp-block-file__button wp-element-button\" download=\"\" aria-describedby=\"wp-block-file--media-9fb9465d-d03e-4c90-b2d7-109f3b70d3c2\">Download<\/a><\/div>\n\n<p class=\"wp-block-paragraph\">G105 is generally reviewed for deep or directional sections with controlled gancho load, rotaria par and dogleg-related bending. S135 is more suitable when long lateral rotation, ERD par-arrastre, high gancho load or repeated bending near the upset transition and uni\u00f3n creates higher fatiga exposure and uni\u00f3n-side demand.The grado ranges in this table should be treated as engineering review boundaries rather than fixed selection rules. G105 tuber\u00eda de perforaci\u00f3n can be enough for a <a href=\"__PROTECTED_0__\">deep or directional pozo<\/a> when tensile margin, dogleg severity and uni\u00f3n capacity remain controlled. S135 tuber\u00eda de perforaci\u00f3n becomes more relevant when high gancho load, long horizontal rotation, ERD par-arrastre or severe bending makes G105 margin insufficient.<\/p>\n\n<h2 class=\"wp-block-heading\">grado Selection Must Match Size, Upset Type and uni\u00f3n<\/h2>\n\n<p class=\"wp-block-paragraph\"><strong>API 5DP grade selection should be checked together with the physical drill pipe design, not only the steel strength level.<\/strong> Even when the pipe body meets G105 or S135 strength, the final drill string performance can still be limited by wall thickness, internal clearance after upset, tool joint bore, connection torque capacity, shoulder contact or fatigue concentration near the upset transition.<\/p>\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-center\" data-align=\"center\">Review Area<\/th><th>Why It Matters<\/th><\/tr><\/thead><tbody><tr><td class=\"has-text-align-center\" data-align=\"center\">OD \/ espesor de pared \/ nominal peso<\/td><td>Affects tensile capacity, internal clearance, handling peso and sarta de perforaci\u00f3n design.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\"><a href=\"https:\/\/www.drillpipes.com\/es\/ieu-eu-e-iu-tuberia-de-perforacion-que-cambia-el-tipo-de-ensanchado\/\">IU \/ EU \/ IEU upset type<\/a><\/td><td>Changes the transition geometry and internal or external clearance near the tuber\u00eda end.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">uni\u00f3n OD \/ ID<\/td><td>Controls uni\u00f3n strength, bore clearance and par-transfer capability.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">uni\u00f3n and shoulder contact<\/td><td>Determines make-up par, rosca engagement and load transfer.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Weld zone and transition area<\/td><td>Needs review because fatiga often concentrates near geometry changes.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n<p class=\"wp-block-paragraph\"><strong>For G105 Drill Pipe and S135 Drill Pipe, the review should identify the first mechanical limit in the complete drill pipe assembly.<\/strong> Increasing the pipe-body grade improves tensile margin, but the operating load still passes through the upset transition, weld zone, tool joint bore, thread profile and shoulder face. If wall thickness, internal clearance, shoulder contact or tool joint dimensions are not matched to the same load case, the selected grade only strengthens the pipe body while the connection area remains the controlling risk point.<\/p>\n\n<h2 class=\"wp-block-heading\">Inspection Records for API 5DP tuber\u00eda de perforaci\u00f3n grado Acceptance<\/h2>\n\n<p class=\"wp-block-paragraph\">API 5DP tuber\u00eda de perforaci\u00f3n grado acceptance should be verified through a <a href=\"__PROTECTED_0__\">traceable record chain<\/a>, not only by the grado marking on the tuber\u00eda. The selected grado must be linked to the tuber\u00eda identity, heat number, MTC, mechanical test results, dimensional inspection and uni\u00f3n \/ rosca inspection. This ensures that E75, X95, G105 or S135 is supported by measurable test evidence and that the tuber\u00eda body, uni\u00f3n and release documents refer to the same delivered tuber\u00eda de perforaci\u00f3n.<\/p>\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th class=\"has-text-align-center\" data-align=\"center\">Record Item<\/th><th>Why It Matters<\/th><\/tr><\/thead><tbody><tr><td class=\"has-text-align-center\" data-align=\"center\">tuber\u00eda marking<\/td><td>Confirms grado, size, uni\u00f3n and product identity.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Heat number<\/td><td>Links the tuber\u00eda body and test data to the production heat.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">MTC<\/td><td>Shows chemical composition and mechanical property basis.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Tensile test<\/td><td>Verifies l\u00edmite el\u00e1stico, resistencia a la tracci\u00f3n and elongation.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Charpy iMPact test<\/td><td>Supports toughness review where required by grado, PSL or project specification.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Hardness record<\/td><td>Important for high-strength grado review, sour-service control or cracking-risk evaluation.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">NDT report<\/td><td>Supports tuber\u00eda body, weld zone and defect control.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Dimensional inspection<\/td><td>Confirms OD, espesor de pared, length, straightness and upset area.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">uni\u00f3n inspection<\/td><td>Confirms uni\u00f3n dimensions, rosca condition and shoulder quality.<\/td><\/tr><tr><td class=\"has-text-align-center\" data-align=\"center\">Final release record<\/td><td>Connects the inspected product with the required grado and specification basis.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n<p class=\"wp-block-paragraph\">A clear record chain should connect each inspection item in order:<br\/>tuber\u00eda marking \u2192 Heat number \u2192 MTC \u2192 Mechanical test report \u2192 Charpy iMPact test where required \u2192 Hardness record where required \u2192 NDT report \u2192 Dimensional inspection report \u2192 uni\u00f3n and rosca inspection \u2192 Final release record.<\/p>\n\n<h2 class=\"wp-block-heading\">When API 5DP grados Are Not Enough<\/h2>\n\n<p class=\"wp-block-paragraph\">Most perforaci\u00f3n programs can be reviewed within the <strong>API 5DP tuber\u00eda de perforaci\u00f3n grados<\/strong> system when the selected grado, size, uni\u00f3n and inspection records support the calculated load path. The limitation appears when the controlling factor is no longer basic l\u00edmite el\u00e1stico, but cracking risk, low-temperature toughness, fatiga accumulation or uni\u00f3n-side performance.<\/p>\n\n<p class=\"wp-block-paragraph\">A tramoard API grado becomes insufficient when the controlling factor is:<\/p>\n\n<ul class=\"wp-block-list\">\n<li>severe sour-service or H2S exposure<\/li>\n\n\n\n<li>low-temperature iMPact toughness<\/li>\n\n\n\n<li>very long horizontal rotation<\/li>\n\n\n\n<li>severe dogleg fatiga<\/li>\n\n\n\n<li>high par beyond normal uni\u00f3n review<\/li>\n\n\n\n<li>special uni\u00f3n or uni\u00f3n matching<\/li>\n\n\n\n<li>tighter hardness or microstructure control<\/li>\n\n\n\n<li>controlled yield-strength window requirement<\/li>\n<\/ul>\n\n<p class=\"wp-block-paragraph\">When the limiting factor moves beyond tramoard grado strength, the review shifts from <strong>API 5DP tuber\u00eda de perforaci\u00f3n grados<\/strong> to a <a href=\"__PROTECTED_0__\"><strong>Special Material tuber\u00eda de perforaci\u00f3n<\/strong> route<\/a>, where chemistry, heat treatment, hardness, iMPact toughness, fatiga-sensitive geometry, uni\u00f3n matching and traceability records become the main control points.<\/p>\n\n<div class=\"wp-block-buttons is-content-justification-center is-layout-flex wp-container-core-buttons-is-layout-d61d70aa wp-block-buttons-is-layout-flex\">\n<div class=\"wp-block-button\"><a class=\"wp-block-button__link has-primary-color has-secondary-background-color has-text-color has-background has-link-color wp-element-button\" href=\"https:\/\/www.drillpipes.com\/es\/contacto\/\">Free quotation<\/a><\/div>\n<\/div>\n\n<h2 class=\"wp-block-heading has-secondary-color has-text-color has-link-color wp-elements-1\">FAQ<\/h2>\n\n<details class=\"wp-block-details is-layout-flow wp-block-details-is-layout-flow\"><summary>F1:What is the difference between E75, X95, G105 and S135 tuber\u00eda de perforaci\u00f3n?<\/summary>\n<p class=\"wp-block-paragraph\">Q1:The main difference is the API 5DP strength level. <strong>E75 tuber\u00eda de perforaci\u00f3n<\/strong> starts at <strong>75 ksi minimum l\u00edmite el\u00e1stico<\/strong>, <strong>X95<\/strong> at <strong>95 ksi<\/strong>, <strong>G105<\/strong> at <strong>105 ksi<\/strong> and <strong>S135<\/strong> at <strong>135 ksi<\/strong>. The grado should not be selected by l\u00edmite el\u00e1stico alone. pozo depth, gancho load, par, dogleg severity, fatiga exposure, upset type, uni\u00f3n condition and inspection records should be reviewed together.<\/p>\n<\/details>\n\n<details class=\"wp-block-details is-layout-flow wp-block-details-is-layout-flow\"><summary>F2:Is S135 tuber\u00eda de perforaci\u00f3n always better than G105 tuber\u00eda de perforaci\u00f3n?<\/summary>\n<p class=\"wp-block-paragraph\">Q2:No. <strong>S135 tuber\u00eda de perforaci\u00f3n<\/strong> has a higher strength level than <strong>G105 tuber\u00eda de perforaci\u00f3n<\/strong>, but it is not automatically the better grado. If G105 provides enough tensile margin and the uni\u00f3n, dogleg severity, par and fatiga exposure remain controlled, G105 can be the more suitable API 5DP grado. S135 becomes more relevant when high gancho load, long horizontal rotation or severe bending makes the G105 margin insufficient.<\/p>\n<\/details>\n\n<details class=\"wp-block-details is-layout-flow wp-block-details-is-layout-flow\"><summary>F3:How should API 5DP tuber\u00eda de perforaci\u00f3n grado be selected for deep or horizontal pozos?<\/summary>\n<p class=\"wp-block-paragraph\">Q3:For deep or horizontal pozos, <strong>API 5DP tuber\u00eda de perforaci\u00f3n grado selection<\/strong> should start with gancho load and tensile margin, then move to par-arrastre, dogleg severity, cyclic bending and uni\u00f3n capacity. <strong>G105 tuber\u00eda de perforaci\u00f3n<\/strong> is often reviewed for deeper or directional sections with controlled fatiga exposure. <strong>S135 tuber\u00eda de perforaci\u00f3n<\/strong> is reviewed when higher gancho load, long lateral rotation or high par makes the sarta de perforaci\u00f3n load path more demanding.<\/p>\n<\/details>\n\n<details class=\"wp-block-details is-layout-flow wp-block-details-is-layout-flow\"><summary>F4:What records verify API 5DP tuber\u00eda de perforaci\u00f3n grados?<\/summary>\n<p class=\"wp-block-paragraph\">Q4:API 5DP grado verification should be supported by a traceable record chain, not only by tuber\u00eda marking. The key records include <strong>heat number, MTC, tensile test, Charpy iMPact test where required, hardness record where required, NDT report, dimensional inspection, uni\u00f3n inspection and rosca inspection<\/strong>. These records confirm whether E75, X95, G105 or S135 is supported by actual test evidence for the delivered tuber\u00eda de perforaci\u00f3n.<\/p>\n<\/details>\n\n<figure class=\"wp-block-gallery has-nested-images columns-default is-cropped wp-block-gallery-4 is-layout-flex wp-block-gallery-is-layout-flex\">\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"410\" data-id=\"12635\" src=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/05\/OCTAL-Certifications-1024x410.png\" alt=\"\" class=\"wp-image-12635\" srcset=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/05\/OCTAL-Certifications-1024x410.png 1024w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/05\/OCTAL-Certifications-300x120.png 300w, https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/05\/OCTAL-Certifications-2000x800.png 2000w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n<\/figure>\n","protected":false},"excerpt":{"rendered":"<p>API 5DP Drill Pipe Grade Selection compares E75, X95, G105 and S135 by strength level, load condition and drill string performance. E75 starts at 75 ksi minimum yield strength, X95 at 95 ksi, G105 at 105 ksi and S135 at 135 ksi, but grade selection should not move upward only because the number is higher. &hellip; <\/p>\n<p class=\"link-more\"><a href=\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/\" class=\"more-link\">Leer m\u00e1s<span class=\"screen-reader-text\"> \u00abAPI 5DP tuber\u00eda de perforaci\u00f3n grado Selection: E75, X95, G105 and S135 CoMPared\u00bb<\/span><\/a><\/p>\n","protected":false},"author":2,"featured_media":15734,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_eb_attr":"","footnotes":""},"categories":[104],"tags":[],"class_list":["post-15730","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog"],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v27.1.1 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>API 5DP tuber\u00eda de perforaci\u00f3n grado Selection<\/title>\n<meta name=\"description\" content=\"CoMPare API 5DP tuber\u00eda de perforaci\u00f3n grados E75, X95, G105 and S135 by strength, perforaci\u00f3n condition, par, fatiga, uni\u00f3n and records.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/\" \/>\n<meta property=\"og:locale\" content=\"es_ES\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection\" \/>\n<meta property=\"og:description\" content=\"CoMPare API 5DP tuber\u00eda de perforaci\u00f3n grados E75, X95, G105 and S135 by strength, perforaci\u00f3n condition, par, fatiga, uni\u00f3n and records.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/\" \/>\n<meta property=\"og:site_name\" content=\"Drillpipes\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/kevin.wen.3990\/yoast\" \/>\n<meta property=\"article:published_time\" content=\"2026-06-16T03:40:26+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-09-18T08:02:39+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"500\" \/>\n\t<meta property=\"og:image:height\" content=\"362\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Lynx Bai\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Escrito por\" \/>\n\t<meta name=\"twitter:data1\" content=\"Lynx Bai\" \/>\n\t<meta name=\"twitter:label2\" content=\"Tiempo de lectura\" \/>\n\t<meta name=\"twitter:data2\" content=\"14 minutos\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#article\",\"isPartOf\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/\"},\"author\":{\"name\":\"Lynx Bai\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/#\/schema\/person\/f813bbf4962cabb7ae7583f03f51bd2e\"},\"headline\":\"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection: E75, X95, G105 and S135 CoMPared\",\"datePublished\":\"2026-06-16T03:40:26+00:00\",\"dateModified\":\"2026-09-18T08:02:39+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/\"},\"wordCount\":2974,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/#organization\"},\"image\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg\",\"articleSection\":[\"Blog\"],\"inLanguage\":\"es\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/\",\"url\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/\",\"name\":\"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection\",\"isPartOf\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#primaryimage\"},\"image\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg\",\"datePublished\":\"2026-06-16T03:40:26+00:00\",\"dateModified\":\"2026-09-18T08:02:39+00:00\",\"description\":\"CoMPare API 5DP tuber\u00eda de perforaci\u00f3n grados E75, X95, G105 and S135 by strength, perforaci\u00f3n condition, par, fatiga, uni\u00f3n and records.\",\"breadcrumb\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#breadcrumb\"},\"inLanguage\":\"es\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"es\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#primaryimage\",\"url\":\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg\",\"contentUrl\":\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg\",\"width\":500,\"height\":362},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"\u9996\u9875\",\"item\":\"https:\/\/www.drillpipes.com\/es\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection: E75, X95, G105 and S135 CoMPared\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/#website\",\"url\":\"https:\/\/www.drillpipes.com\/es\/\",\"name\":\"Drillpipes\",\"description\":\"Drill Pipe Supplier for Oil &amp; Gas Drilling | OCTAL\",\"publisher\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/www.drillpipes.com\/es\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"es\"},{\"@type\":\"Organization\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/#organization\",\"name\":\"Drillpipes\",\"url\":\"https:\/\/www.drillpipes.com\/es\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"es\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/#\/schema\/logo\/image\/\",\"url\":\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/03\/drill-pipe-octal-logo.png\",\"contentUrl\":\"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/03\/drill-pipe-octal-logo.png\",\"width\":1134,\"height\":378,\"caption\":\"Drillpipes\"},\"image\":{\"@id\":\"https:\/\/www.drillpipes.com\/es\/#\/schema\/logo\/image\/\"},\"sameAs\":[\"https:\/\/www.facebook.com\/kevin.wen.3990\/yoast\",\"https:\/\/www.youtube.com\/@octalsteel\/yoast\",\"https:\/\/www.linkedin.com\/company\/octalsteel\/yoast\",\"https:\/\/www.tiktok.com\/@octalsteel\/yoast\"]},{\"@type\":\"Person\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/#\/schema\/person\/f813bbf4962cabb7ae7583f03f51bd2e\",\"name\":\"Lynx Bai\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"es\",\"@id\":\"https:\/\/www.drillpipes.com\/es\/#\/schema\/person\/image\/\",\"url\":\"https:\/\/secure.gravatar.com\/avatar\/fae3fe4bee4b43be4ff236a08fa35d8f059e06f563d67572b0867f1a53d63e55?s=96&d=mm&r=g\",\"contentUrl\":\"https:\/\/secure.gravatar.com\/avatar\/fae3fe4bee4b43be4ff236a08fa35d8f059e06f563d67572b0867f1a53d63e55?s=96&d=mm&r=g\",\"caption\":\"Lynx Bai\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection","description":"CoMPare API 5DP tuber\u00eda de perforaci\u00f3n grados E75, X95, G105 and S135 by strength, perforaci\u00f3n condition, par, fatiga, uni\u00f3n and records.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/","og_locale":"es_ES","og_type":"article","og_title":"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection","og_description":"CoMPare API 5DP tuber\u00eda de perforaci\u00f3n grados E75, X95, G105 and S135 by strength, perforaci\u00f3n condition, par, fatiga, uni\u00f3n and records.","og_url":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/","og_site_name":"Drillpipes","article_publisher":"https:\/\/www.facebook.com\/kevin.wen.3990\/yoast","article_published_time":"2026-06-16T03:40:26+00:00","article_modified_time":"2026-09-18T08:02:39+00:00","og_image":[{"width":500,"height":362,"url":"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg","type":"image\/jpeg"}],"author":"Lynx Bai","twitter_card":"summary_large_image","twitter_misc":{"Escrito por":"Lynx Bai","Tiempo de lectura":"14 minutos"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#article","isPartOf":{"@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/"},"author":{"name":"Lynx Bai","@id":"https:\/\/www.drillpipes.com\/es\/#\/schema\/person\/f813bbf4962cabb7ae7583f03f51bd2e"},"headline":"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection: E75, X95, G105 and S135 CoMPared","datePublished":"2026-06-16T03:40:26+00:00","dateModified":"2026-09-18T08:02:39+00:00","mainEntityOfPage":{"@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/"},"wordCount":2974,"commentCount":0,"publisher":{"@id":"https:\/\/www.drillpipes.com\/es\/#organization"},"image":{"@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#primaryimage"},"thumbnailUrl":"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg","articleSection":["Blog"],"inLanguage":"es","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/","url":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/","name":"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection","isPartOf":{"@id":"https:\/\/www.drillpipes.com\/es\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#primaryimage"},"image":{"@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#primaryimage"},"thumbnailUrl":"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg","datePublished":"2026-06-16T03:40:26+00:00","dateModified":"2026-09-18T08:02:39+00:00","description":"CoMPare API 5DP tuber\u00eda de perforaci\u00f3n grados E75, X95, G105 and S135 by strength, perforaci\u00f3n condition, par, fatiga, uni\u00f3n and records.","breadcrumb":{"@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#breadcrumb"},"inLanguage":"es","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/"]}]},{"@type":"ImageObject","inLanguage":"es","@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#primaryimage","url":"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg","contentUrl":"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/06\/API-5DP-Drill-Pipe-Grade-Selection.jpg","width":500,"height":362},{"@type":"BreadcrumbList","@id":"https:\/\/www.drillpipes.com\/es\/api-5dp-tuberia-de-perforacion-grado-selection-e75-x95-g105-and-s135-compared\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"\u9996\u9875","item":"https:\/\/www.drillpipes.com\/es\/"},{"@type":"ListItem","position":2,"name":"API 5DP tuber\u00eda de perforaci\u00f3n grado Selection: E75, X95, G105 and S135 CoMPared"}]},{"@type":"WebSite","@id":"https:\/\/www.drillpipes.com\/es\/#website","url":"https:\/\/www.drillpipes.com\/es\/","name":"Drillpipes","description":"Drill Pipe Supplier for Oil &amp; Gas Drilling | OCTAL","publisher":{"@id":"https:\/\/www.drillpipes.com\/es\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.drillpipes.com\/es\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"es"},{"@type":"Organization","@id":"https:\/\/www.drillpipes.com\/es\/#organization","name":"Drillpipes","url":"https:\/\/www.drillpipes.com\/es\/","logo":{"@type":"ImageObject","inLanguage":"es","@id":"https:\/\/www.drillpipes.com\/es\/#\/schema\/logo\/image\/","url":"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/03\/drill-pipe-octal-logo.png","contentUrl":"https:\/\/www.drillpipes.com\/wp-content\/uploads\/2026\/03\/drill-pipe-octal-logo.png","width":1134,"height":378,"caption":"Drillpipes"},"image":{"@id":"https:\/\/www.drillpipes.com\/es\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/kevin.wen.3990\/yoast","https:\/\/www.youtube.com\/@octalsteel\/yoast","https:\/\/www.linkedin.com\/company\/octalsteel\/yoast","https:\/\/www.tiktok.com\/@octalsteel\/yoast"]},{"@type":"Person","@id":"https:\/\/www.drillpipes.com\/es\/#\/schema\/person\/f813bbf4962cabb7ae7583f03f51bd2e","name":"Lynx Bai","image":{"@type":"ImageObject","inLanguage":"es","@id":"https:\/\/www.drillpipes.com\/es\/#\/schema\/person\/image\/","url":"https:\/\/secure.gravatar.com\/avatar\/fae3fe4bee4b43be4ff236a08fa35d8f059e06f563d67572b0867f1a53d63e55?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/fae3fe4bee4b43be4ff236a08fa35d8f059e06f563d67572b0867f1a53d63e55?s=96&d=mm&r=g","caption":"Lynx Bai"}}]}},"_links":{"self":[{"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/posts\/15730","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/comments?post=15730"}],"version-history":[{"count":1,"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/posts\/15730\/revisions"}],"predecessor-version":[{"id":15735,"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/posts\/15730\/revisions\/15735"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/media\/15734"}],"wp:attachment":[{"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/media?parent=15730"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/categories?post=15730"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.drillpipes.com\/es\/wp-json\/wp\/v2\/tags?post=15730"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}